Weck Gem Pass Around

I am offering my Weck Gem 3D Printed razor for a pass around. This razor uses the same Gem blades as the EndGem and loads the same way using your thumb and index fingers to slide the blade back into the head's grooves on either side of the razor. The shave I consider medium aggressive with more blade feel and less noise. Again it a one piece razor as the handle is attached to the head using epoxy. This razor weighs only 11 grams. The head should be totally flat against your face and neck to shave properly. Under the nose I recommend ATG and CTG.  Razors created by Roger (Slim Gem).

First come first serve. PM me if interested. Sorry for USA addresses only.

I'm in 

Copy and Paste below this line and add your name to the list to join the pass around
______________________________________________________________________

1. Dave in KY
2.
3.
4.
5.
6.
7.
8.
9.

Copy and Paste below this line and add your name to the list to join the pass around
______________________________________________________________________

1. Dave in KY
2.gvw755 WA state
3.
4.
5.
6.
7.
8.
9.

Shipped out to Dave this morning. If you are interested in trying out this Gem razor put yourself on the list.

Thanks very much slantman.  

Copy and Paste below this line and add your name to the list to join the pass around
______________________________________________________________________

1. Dave in KY
2.gvw755 WA state
3. HighSpeed
4.
5.
6.
7.
8.
9.

[font=Tahoma, Verdana, Arial, sans-serif]Copy and Paste below this line and add your name to the list to join the pass around[/font]
[font=Tahoma, Verdana, Arial, sans-serif]______________________________________________________________________[/font]

[font=Tahoma, Verdana, Arial, sans-serif]1. Dave in KY[/font]
[font=Tahoma, Verdana, Arial, sans-serif]2. [font=Tahoma, Verdana, Arial, sans-serif]HighSpeed[/font][/font]
[font=Tahoma, Verdana, Arial, sans-serif]3. gvw755[/font]
[font=Tahoma, Verdana, Arial, sans-serif]4.[/font]
[font=Tahoma, Verdana, Arial, sans-serif]5.[/font]
[font=Tahoma, Verdana, Arial, sans-serif]6.[/font]
[font=Tahoma, Verdana, Arial, sans-serif]7.[/font]
[font=Tahoma, Verdana, Arial, sans-serif]8.[/font]
[font=Tahoma, Verdana, Arial, sans-serif]9.[/font]


[font=Tahoma, Verdana, Arial, sans-serif]switching the order because HighSpeed is on the east coast.[/font]

Thanks very much gvw755. 

gvw755 and I have been corresponding via PM.  It occurred to him that I am much closer to Dave than he is, and that routing the razor to me first would save an extra coast-to-coast trip.  Given current transit times, saving a coast-to-coast trip will noticeably reduce the overall wait for us as a group.  That is why, as he mentioned, he switched the pass around order accordingly.  IMO that is commendably community minded.

Thanks very much gvw755. 

gvw755 and I have been corresponding via PM.  It occurred to him that I am much closer to Dave than he is, and that routing the razor to me first would save an extra coast-to-coast trip.  Given current transit times, saving a coast-to-coast trip will noticeably reduce the overall wait for us as a group.  That is why, as he mentioned, he switched the pass around order accordingly.  IMO that is commendably community minded.

I totally agree. FYI the post office raised rates 1/24 so shipping to a shorter distance savings not only time but money. I am fairly close to Dave so sending him the razor first makes sense.

Package arrived today and all looked fine.....................until I opened the box which was not crushed or damaged at all. Epoxy apparently didn't hold up. Waiting to hear from Jerry

Package arrived today and all looked fine.....................until I opened the box which was not crushed or damaged at all. Epoxy apparently didn't hold up. Waiting to hear from Jerry

It looks like the stud from the head which was one piece broke off. If you look at the handle you should see the stud. It was not an epoxy failure just a weak piece. I doubt it could be fixed.  I will contact you Dave.
Jerry