#1

Member
Seattle, WA (USA)
(This post was last modified: 03-11-2020, 06:36 PM by draebeard.)
I recently bought a post-war vintage zamac razor in NOS condition.  Unfortunately the tip of the threaded center post didn't get plated.  
It is presently in undamaged condition.  What can do to keep it that way?  Here is a picture.  I invite your suggestions.  Thank you. 

[Image: R4oXi1E.jpg]
#2

Posting Freak
Peachtree City, GA
What we do in motorsports for exposed threaded fasteners:
Spray wax ala ChainWax
Melted Wax ala bicycles
Copper or nickel based antiseize

Marhos24, Steve56 and Fenster like this post
#3
Maybe a reputable place to re-plate that post for you? I am totally spit-balling here.
#4

Member
Los Angeles
(This post was last modified: 03-31-2020, 10:00 PM by Tidepool.)
(03-11-2020, 06:34 PM)draebeard Wrote: I recently bought a post-war vintage zamac razor in NOS condition.  Unfortunately the tip of the threaded center post didn't get plated.  
It is presently in undamaged condition.  What can do to keep it that way?  Here is a picture.  I invite your suggestions.  Thank you. 

[Image: R4oXi1E.jpg]
I own several Harleys.  One of them (that I built was in Easy Rider and the Mikuni calendar).  So, I have had a lot of parts chrome plated.  Generally, you should never plate threads because it add thickness and it could cause the piece to freeze in the bottom threads.  The gentleman from George makes a good point.  If you are going to screw it to the bottom you can use a silver anti-seize.  However, apply it sparingly because it could get messy.  I have never done this but a thin coat of wax may also work.  Good luck

Max Sprecher likes this post
#5

Member
AZ, USA
(This post was last modified: 04-01-2020, 01:35 AM by TheHunter.)
[Image: bl2JrkZ.jpg]

I use a small drop of this, synthetic sewing machine oil, on all my Razors threads after using and then cleaning them.

zaclikestoshave likes this post
Hunter
#6

Member
Singapore
(04-01-2020, 01:22 AM)TheHunter Wrote: I use a small drop of this, synthetic sewing machine oil, on all my Razors threads after using and then cleaning them.
Why? Doesn't this increase the likelihood of loosening of handle (and thus top cap and base plate) in the midst of the shave? Thanks for clarifying.
#7

Member
AZ, USA
(04-01-2020, 02:39 AM)Zhang Doe Wrote:
(04-01-2020, 01:22 AM)TheHunter Wrote: I use a small drop of this, synthetic sewing machine oil, on all my Razors threads after using and then cleaning them.
Why? Doesn't this increase the likelihood of loosening of handle (and thus top cap and base plate) in the midst of the shave? Thanks for clarifying.

I put a drop of oil on my threads to protect them from metal on metal wear. That’s what the OP is asking about, how to prevent wear to his threads. I also use nylon washers on all of my Razors between the baseplate and handle to prevent any marring from metal on metal contact. When I shave I cinch it down tight, and I’ve never had a handle get loose during a shave.

Max Sprecher and LOOT like this post
Hunter
#8
(04-01-2020, 03:30 AM)TheHunter Wrote: I put a drop of oil on my threads to protect them from metal on metal wear. That’s what the OP is asking about, how to prevent wear to his threads. I also use nylon washers on all of my Razors between the baseplate and handle to prevent any marring from metal on metal contact. When I shave I cinch it down tight, and I’ve never had a handle get loose during a shave.

Where can I get these washers? What are the specs? Thanks!

Sent from my Pixel 2 XL using Tapatalk
#9

Just Here for the Shaves
Williamsburg, KY
(This post was last modified: 04-01-2020, 01:48 PM by Dave in KY.)
(04-01-2020, 01:23 PM)fhalden Wrote:
(04-01-2020, 03:30 AM)TheHunter Wrote: I put a drop of oil on my threads to protect them from metal on metal wear. That’s what the OP is asking about, how to prevent wear to his threads. I also use nylon washers on all of my Razors between the baseplate and handle to prevent any marring from metal on metal contact. When I shave I cinch it down tight, and I’ve never had a handle get loose during a shave.

Where can I get these washers? What are the specs? Thanks!

Sent from my Pixel 2 XL using Tapatalk
Size = M5 x 10mm x 1mm nylon flat washers
These are the ones I bought some time ago. 100 for a little more than a Dollar
https://www.ebay.com/itm/153246933196

TheHunter likes this post
This post by Dave in KY mentions views and opinions expressed and makes it known that they are "those of the author and do not necessarily reflect the official policy or position of DFS or any other member, agency, organization, employer or company."  Big Grin


Users browsing this thread: